Optimization of C/TiCx duplex diffusion barrier coatings for SiCf/Ti composites based on interfacial structure evolution exploration

Introducing a carbon single coating is a popular method used to protect SiC_f/Ti composites from severe interface reactions. However, carbon coatings lose their protective effect on SiC fibres at high temperature, even after a short period time. As such, given the strong demand for high temperature applications in aeronautics and astronautics a more coating which is more effective at high temperatures is desirable. In order to improve the high temperature interfacial stability of SiC_f/Ti composites, a C/TiC_x duplex coating system with different C contents in TiC_x was introduced to explore the protection of fibres at 1200?°C for 1?h. The results show that the C/quasi-stoichiometric TiC coating system protects the SiC fibres most effectively. Based on insights from the evolution of the interface structure, TiC_x has been identified as an interfacial reaction product from the C single coating, exhibiting a gradient in C content and grain size, which is different from a deposited TiC layer with a well-distributed composition and structure. The different coating structure gives rise to different ability to resist C diffusion at high temperatures, in which poor resistance ability appears in TiC_x interfacial reaction layer coming from C single coating due to short-circuit diffusion in C-rich fine-grained TiC layer and fast intracrystalline diffusion trigged by amounts of vacancies in sub-stoichiometric coarse-grained TiC layer. Therefore, C/quasi-stoichiometric TiC duplex coatings with a thick, coarse-grained quasi-stoichiometric TiC layer could effectively inhibit C diffusion by comparison to C single coatings, and is more effective than C/rich-carbon TiC duplex coatings due to the existence of short-circuit diffusion in the latter. As such, C/quasi-stoichiometric TiC duplex coatings appear to be an optimal diffusion barrier for SiC_f/Ti composites at high temperature.     

Investigation of spitting behaviour of NiCoCrAlY type materials during electron beam evaporation

ABSTRACT

Spitting behaviour of four casted and powder metallurgy ingots used in the fabrication of NiCoCrAlY-type environmental protective coatings by electron beam physical vapour deposition was investigated and correlated with ingot microstructures and compositions. Spits found in the coatings mainly consisted of the Ni₅Y phase precipitated in the β-NiAl matrix while their typical size exceeded 50?µm. Spitting was less pronounced for ingots having a higher Cr content, larger size of γ-Ni(Co, Cr) precipitates formed within β-NiAl grains and narrower transitional zone formed at the interface between molten and unmolten ingot regions and consisting of coarsened β grains. Large (above 100?µm) agglomerates of the Ni₅Y phase detected below the zone were identified as the main spit precursors.     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.     

某复杂金多金属矿石选矿试验研究

吉尔吉斯斯坦某金多金属矿石中伴生多种有价元素,有用矿物嵌布状态复杂且嵌布粒度细。针对矿石性质,采用铜优先浮选—金钴混合浮选工艺流程,可初步实现该金多金属矿石中有价金属的有效分选。闭路试验可获得Au品位228.00 g/t、Au回收率12.19%,Ag品位974.00 g/t、Ag回收率37.71%,Cu品位27.590%、Cu回收率80.65%的铜精矿,以及Au品位65.00 g/t、Au回收率57.22%,Ag品位28.00 g/t、Ag回收率17.86%,Co品位0.5500%、Co回收率53.02%的金钴精矿。     

Bioinspired Supramolecular Slippery Organogels for Controlling Pathogen Spread by Respiratory Droplets

Surface-deposited pathogens are sources for the spread of infectious diseases. Protecting public facilities with a replaceable or recyclable antifouling coating is a promising approach to control pathogen transmission. However, most antifouling coatings are less effective in preventing pathogen-contained respiratory droplets because these tiny droplets are difficult to repel, and the deposited pathogens can remain viable from hours to days. Inspired by mucus, an antimicrobial supramolecular organogel for the control of microdroplet-mediated pathogen spread is developed. The developed organogel coating harvests a couple of unique features including localized molecular control-release, readily damage healing, and persistent fouling-release properties, which are preferential for antifouling coating. Microdroplets deposited on the organogel surfaces will be spontaneously wrapped with a thin liquid layer, and will therefore be disinfected rapidly due to a mechanism of spatially enhanced release of bactericidal molecules. Furthermore, the persistent fouling-release and damage-healing properties will significantly extend the life-span of the coating, making it promising for diverse applications.     

Poly(4-styrenesulfonic acid) doped polypyrrole/tungsten oxide/reduced graphene oxide nanocomposite films based surface acoustic wave sensors for NO sensing behavior

Poly(4-styrenesulfonic acid) (PSSA) doped polypyrrole (PPy)/tungsten oxide (WO₃)/reduced graphene oxide (rGO) hybrid nanocomposite have been successfully synthesized using appropriate amounts of PSSA, pyrrole monomer, WO₃, and rGO dispersed in aqueous solution through in situ chemical oxidation polymerization. Here, a simple spin coating method was used to fabricate a nitric oxide (NO) gas sensor composed of the aforementioned nanocomposite on a surface acoustic wave (SAW) resonator. This sensor can detect NO gas at concentrations of 1–110 parts per billion (ppb) at room temperature in dry air, with a sensitivity of 12 Hz/ppb and response and recovery times of <2 min. Moreover, its limit of detection (LOD) is 0.31 ppb for a signal to noise ratio of 3. It demonstrates repeatability, fast response, and recovery at room temperature. Moreover, its sensory performance remains highly stable over 30 days with only a 6.3% decrease in sensitivity. In addition, the sensor is highly selective for NO, even when nitrogen dioxide, ammonia, and carbon dioxide are applied as interfering gases. The inclusion of rGO (with large specific surface area) and the synergic effect of n-type WO₃ nanoparticles in the p-type PPy matrix (leading to p-n heterojunction region formation) possibly underlie the efficient sensing performance of our sensor.     

Densification and anticorrosion performances of vacuum evaporated aluminium coatings on NdFeB magnets

Al coated NdFeB magnets obtained by vacuum evaporation technique were densified by high energy ball milling method.The surface morphology,metal composition and micro structure of the coatings were characterized by scanning electron microscopy,X-ray diffraction and X-ray photoelectron spectroscopy,respectively.The anticorrosive properties were investigated by potentiodynamic polarization curves and neutral salt spray test.The pores in the Al coatings of columnar crystals(Al) induced by the evaporation technique,were apparently filled in the following ball milling process,leading to the densification of Al coatings and the evident improvement of the anticorrosive performances.When treated with ball milling for 30 min,the sample achieves the best anticorrosive performances with the self-corrosion potential of-0.87 V,self-corrosion current density of 1.65 μA/cm~2 and the neutral salt spray(NSS) time of 144 h(red rust).The improvement of the anticorro sive performances of vacuum evaporated Al coating mainly lies in the densification effect of the coating,which depends on different loading conditions of ball milling process.     

Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

The crosslinking directing dynamic behavior of polymer latex under the investigation toward waterborne damping coatings

Latex polymers with precisely designed dynamic mechanical behavior are the key for waterborne damping coatings, which are widely desired in noise and vibration reduction with additional environmental benefits. In this work, we synthesized series of polymer latexes with various crosslinking agents (CA) and network distributions through the control on emulsion polymerization processes. We have revealed that the variation on crosslinking can significantly direct the latex behavior under dynamic conditions as well as its films. The variables involve the CA composition, the functionality, the crosslinking manner, the hydrophilic-hydrophobic feature as well as the feeding method. Although all the latex films showed the damping peaks locating in the range from −10 to 70°C, their damping behaviors were quite different. Suggested by the empirical parameters of LA and TA, the product from sequential monomer feeding method tended to give good extensional damping performance. Especially when the crosslinking of diacetone acrylamide (DAAM)/adipic dihydrazide was applied, there was a linear increase on LA with the increasing dosage of DAAM from 0 to 10 mmol in the final monomer addition batch. Meanwhile, good constrained layer damping is expected on the products from the power monomer feeding method with the maximum CA dosage shown below 7.5 mmol. The best TA was achieved when the CA of divinylbenzene was used in the dosage of 5 mmol. These results would be valuable to be referenced in the engineering on organic damping materials toward modern industrial and vehicles applications.     

Effects of methyl cellulose-based coating on physiochemical properties and chemical hazards of Chinese fried dough cake during storage

Coating has been used as a practical method to ensure the physiochemical properties and reduce the chemical hazard of fried foods. Methyl cellulose (MC) was used as a coating material to pretreat Chinese fried dough cake (CFDC) before frying. The results showed that the water content, hardness and L* value of the 1% MC coated sample were 31.67%, 848.54 g and 51.62, respectively, at the seventh day at 25 °C. Coating contents 1% MC could reduce the oil content, hardness, and extent of browning and improve the physiochemical properties of CFDC on 7 days of storage. Coating contents 1% MC also reduced the acid value, peroxide value, p-anisidine value, malondialdehyde content, 4-hydroxy-2-(E)-hexenal content, 4-hydroxy-2-(E)-nonenal content, acrylamide content and glycidyl ester content in CFDC on 7 days of storage. Our work contributes to the control of the oil content and chemical hazards for fried food during storage by applying an edible coating.